可编程按时器 节制板 Digital Timer Board Tim 01

供给8种现场可编程功效,可节制单刀双掷继电器,按时距离规模为1秒至99天,利用于安防报警、门禁、产业节制体系

  • 输入电压: DC12V
封闭
在线询价
倡议用右侧在线体例相同,更精确实时。


特点

    设想用于供给8种现场可编程功效,可节制单双掷继电器,按时时距离规模为1秒至99天

 

Program Modes  编程形式

 

 

One shot - Applying trigger activates relay for selected time. Trigger input must be removed & re-applied to re-active.

一次性 - 利用触发激活继电器挑选的时候。 必须删除触发器输入偏从头利用能力从头激活。

 

Retriggerable - As for One Shot, except where input is retriggered, the timer starts again.

 

可从头触发 - 对单次拍摄,除从头触发输入,按时器从头起头。


Strobe - Requires momentary trigger to be applied, relay will activate for programmed time.

频闪 - 须要刹时触发,继电器将激活编程时候。


Clutch Relay - Applying trigger causes relay to change state. Removing and re-applying trigger forces relay to change state. No timing function in this mode.

聚散器继电器 - 利用触发器使继电器转变状况。 去除和从头施加触发力继电器转变状况。 此形式下无按时功效。

 

Programmed Pulse - Applying trigger causes relay to operate for one second at programmed intervals. Set intervals on SW2, SW3 & SW4. Operation ceases when trigger is removed.

 编程脉冲 - 利用触发使继电器以编程距离运转一秒钟。 在SW2,SW3和SW4上设置距离。 触发器被移除后,操纵遏制。


Debounce - Applying trigger causes relay to activate for programmed time. Relay remains activated until timeout regardless of trigger being removed. If input remains triggered after timeout, relay remains activated until trigger is removed.

去抖 - 利用触发使继电器激活编程时候。 继电器坚持激活直到超时,不管触发被移除。 若是输入在超时后坚持触发,则继电器坚持激活,直到触发被移除。


Stand-Off Timer - Ideal for DOTL (Door Open Too Long) alarms. Timing commences when trigger is applied. If trigger is removed before timeout, relay will not activate. If trigger remains after timeout, relay will activate.

待机按时器 - 合用于DOTL(门翻开太长)报警。 启动触发时起头计时。 若是触发器在超时之前被删除,继电器将不会激活。 若是超时后触发坚持,则继电器将激活。


Fail Secure - The relay does not change state during power failure.

毛病安稳 - 断电时继电器不转变状况。


Fail Safe - The relay is energised when the trigger is not active. Relay will de-energise (e.g. releasing power to door locks) during a power failure.

毛病宁静 - 当触发器未激活时,继电器通电。 断电时代继电器将断电(比方开释电源到门锁)。


办事热线

131-4639-3780

公司地点

北京市通州区于家务乡北辛店240号

任务时候

周一至周五 8:30~17:00

德律风征询
产物中间